Last Updated: November 19, 2026
Quick Summary
Electrical renovation planning means mapping power points, lighting, switches, data outlets and circuits before walls are closed. Doing this early keeps trades in sequence and makes changes far cheaper than after plasterboard goes up.
Electrical planning is the step most renovations leave too late. Renovation projects often follow the same pattern: walls are lined, ceilings are sheeted and only then does anyone ask where the power points, lighting circuits and data cabling should go. A residential electrical renovation planning guide exists to stop that sequence before it starts.
Electrical decisions made early are generally easier and less disruptive to change than decisions made after plasterboard is up. A switch that should sit beside the entry door ends up behind the sofa because nobody mapped the furniture first.
Early planning also protects the rest of the schedule. Plumbers, carpenters, painters and the electrician all depend on the same rough-in window. When the electrical plan is settled before walls close, trades can work in sequence rather than returning to fix each other's work.
Planning first also gives you a clear view of your existing system. Before you commit to smart switches, dimmers or a new circuit, the switchboard and wiring need to be understood. That assessment sets what the renovation can realistically include.
Start by writing down what the renovation must achieve. A kitchen upgrade, a home office, a new bathroom and an outdoor entertaining area each place different demands on the electrical system, and each should be listed separately.
Next, separate what you want from what the home can support. Ask whether the current switchboard has room for new circuits and whether the existing wiring is in sound condition. Those answers define the real scope, which may be smaller or larger than the original wish list.
A practical scope document usually covers:
Keep future needs in the scope.
A room-by-room checklist keeps the plan complete and prevents the common pattern of discovering a missing outlet after the plasterboard is up. Work through each space with the floor plan in hand and record what it needs.
Kitchen: Plan dedicated circuits for the oven, cooktop, dishwasher and microwave. Include the range hood, under-bench lighting and any integrated charging points.
Living areas: Place power points where furniture will actually stand, not only where the wall is empty. Plan media outlets, data points and ceiling lighting with dimming in mind.
Bedrooms: Include reading light outlets, ceiling fan supply and a data point if the room will be used for work. Consider a two-way switch at the door and beside the bed for the main light.
Bathrooms: Locate the exhaust fan, heater and vanity lighting. Power points in wet areas must meet the required protection and placement rules, so confirm them with a licensed electrician.
Laundry and utility spaces: Allow for washing machine and dryer circuits and a dedicated supply for any hot water or pump equipment.
Hallways and stairs: Plan two-way switching at each end, and consider motion-sensor lighting for night-time safety. Include a power point for a vacuum or a night light.
Garage and workshop: Plan dedicated circuits for power tools, a welder or a compressor. Include weatherproof power points near the garage door for outdoor equipment, and a supply for any future EV charger.
Outdoor areas: Plan weatherproof power points, outdoor lighting, and a supply for any future EV charger or pool equipment.
Mark each item on the floor plan, then compare the plan against the furniture layout. Moving a power point before the wall is opened takes minutes; moving it afterwards takes days.
Turn the checklist into a drawn plan. The plan should show every power point, switch, light point, data outlet and circuit route, using the same floor plan as your scope document.

Give each circuit a clear label on the plan. Note the load each one will carry, so the electrician can confirm the switchboard can support it. A plan without load notes cannot show whether the house can handle a new kitchen and a home office at the same time.
A workable electrical plan includes:
Share the plan with your builder and every trade before rough-in begins. Ask each trade to confirm that the plan does not clash with their work, such as a plumbing pipe running through a planned wall position.
Lighting is where renovation plans most often fall short. Ceiling lights are placed by habit rather than by how each room is used. A better approach layers light in three ways: general ceiling light, task light where you work, and accent light for mood.
Switch positions matter as much as fixture positions. Place switches where you naturally reach when entering a room, and consider two-way switching for hallways and stairs. Plan dimmers in living areas and bedrooms, and confirm that the dimmers you choose suit the lighting type you install.
Document the lighting plan separately from the power plan. Include fixture types, switch locations, dimmer locations and any zones you want to control together. This document also feeds directly into smart lighting decisions later.
A renovation is the most cost-effective time to install smart home wiring because cabling, back boxes and conduit can be placed while walls are open, rather than retrofitted afterwards. The decisions made at this stage determine whether the system works reliably for the next decade or becomes a patchwork of devices that do not communicate.
Start by deciding which systems you want before the electrician starts. Lighting control, blinds, climate control, security cameras and an intercom all need cabling and sometimes dedicated power. Plan them together to avoid duplicated runs and devices that do not communicate. For lighting control, decide whether you want centralised control (with all switching at the switchboard) or distributed control (with smart switches in each room).
Plan the network backbone at the same time, since a reliable smart home benefits from a wired data network as well as Wi-Fi. Include data points for access points, cameras, and any fixed devices, and run conduit so that you can add cables later. If solar or battery storage is part of the plan, confirm that the switchboard design accommodates the inverter and any future battery connection.
Accessibility is another consideration that is easy to overlook. For lighting, layer general, task and accent light so that you can use lower levels of ambient light and reduce energy use. Integrate occupancy sensors in hallways and bathrooms to cut wasted lighting.
Check that your existing smart devices will integrate with the new system. Where they will not, decide early whether to replace them or keep them as standalone units. Document the chosen protocols (such as Wi-Fi, Zigbee, Z-Wave, or a wired bus) and ensure that the electrician and any future integrator can access the documentation.
The main choices for smart lighting control during a renovation are summarised below.
| Approach | Best for | Key difference |
|---|---|---|
| Centralised control | Simple wall plates | More cable runs, switching at the switchboard |
| Distributed control | Easier retrofitting | Needs a neutral wire at every switch |
| Wired data backbone | Reliable smart home | Supports access points, cameras and fixed devices |
| Spare conduit | Future device additions | Avoids reopening walls later |
Book a licensed electrician before rough-in starts and give them your electrical plan, circuit schedule and lighting plan. Ask them to inspect the existing switchboard and wiring and to confirm the scope against what the home can support.
Before any wall is closed, walk through the installed cabling against your plan. Check each power point, switch, light point and data outlet, and confirm the labelling on the switchboard. Photograph the concealed cable routes, since this record is valuable for future renovations.
Confirm the work with your electrician in writing, including the scope, the test results and the handover documentation.
Start by listing what each room must do: where you will work, relax, cook and charge devices. Mark the furniture and appliance positions on a floor plan, then place power points, switches and lighting against those positions. Share the plan with a licensed electrician early so they can check circuit capacity and the existing switchboard before the design is fixed. Revisit the plan at each stage of the renovation so changes to layout are captured while walls are still open.
Involve a licensed electrician during the design stage, before the builder starts framing and before any wiring is roughed in. Early input lets them check the existing wiring, advise on circuit capacity and flag anything that needs upgrading. Waiting until fit-out often means relocating outlets or cutting into finished walls, which costs more and delays the trades that follow. Ask them to confirm the scope of work in writing so it matches your plan.
A useful electrical plan shows each room's power points, light fixtures, switches and dimmers, plus any dedicated circuits for appliances, heating or EV charging. It should also record the existing switchboard condition, the intended smart home devices and any outdoor or data points. Include notes on furniture and appliance positions so outlets are not hidden behind a bed or fridge. Keep the plan as a handover document so future trades and maintenance workers can see what was installed and where.
Walk through each room in its final layout and note the tasks it supports. Place power points where furniture, appliances and charging will sit, and avoid positions that depend on extension leads. For lighting, separate general ceiling light, task light for benches and desks, and accent light for feature areas. Position switches at convenient points near room entries, and plan dimmers where you want flexible mood or reading light. Review the plan at night with the room's real furniture in mind.
Yes, and renovation is the easiest time to do it because cabling can be run before the walls are closed. Decide which lights, blinds, climate controls and sensors you want, then plan the control wiring and network points alongside the standard electrical layout. Confirm with your installer whether your existing smart devices will integrate with the new system or need replacing. Planning automation early avoids retrofit work that would otherwise damage finished surfaces.
Before plasterboard or other linings go up, confirm the position of every outlet, switch, light point, data point and cable run against your plan. Check that circuit routes and conduit sizes match the loads you expect, including future appliances or EV charging. Ask your electrician to photograph the rough-in and mark cable routes on the plan, so future drilling avoids live wiring. Keep these records with your renovation documents for the life of the building.
Plan lighting with LED fittings and separate switching so you light only the areas in use. Add occupancy or daylight sensors in hallways, bathrooms and utility areas where lights are often left on. Position switches and controls so that automation can reduce heating, cooling and standby loads. If you plan solar, batteries or an EV charger, allow for them in the switchboard and cable routes now, since adding them later is harder once the walls are finished.